accessory for dent spotter, body parts spotter, sheet metal working equipment for steel working and other bulging of sheet metals

electronic, fuse T3 / 15 A, supply voltage 12 / 24 V, with reverse polarity protection
To protect the on-board electronics of vehicles from voltage peaks / defects, e.g. due to welding work on the bodywork without disconnecting the battery. The voltage peaks are permanently absorbed and suppressed. It also prevents damage to the on-board electronics when charging or bridging the installed battery. The device is easy to operate. A red LED indicates active overload protection and an acoustic signal sounds in the event of voltage peaks. Connection to the battery is made via two standard crocodile clips.

soda/ sodium bicarbonate, sieve fraction ( smaller as 0,5mm): 95%, water content: smaller as 0,25%
To the eco-friendly soda blasting (baking soda blasting) of all possible surfaces such as glass, plastic, rubber, wood, stone and aluminum. Chloride and sulphate content smaller as 150 ppm

dent removal gun, manual, complete with cable, 2m cable, Ø 70 mm²
Suitable for dent remover: GYSPOT 2700, 34.02, 34.04 - GYSPOT PRO 230, 400 - GYSPOT EXPERT 200, 230, 400

suitable for a variety of blasting agents, e.g. quartz, glass peen shot, plastic peen shot and more
Sandblasting cabin for clean blasting work without soiling the wotk environment. Ideal for cleaning, rust or paint removale from metal parts of all kinds, e.g. engine parts, fittings, signs, housings, rims and hinges. Premium latex work gloves fastened on housing. View window and adhesion-bonded protective film, for the best possible view and occupational protection while processing the workpiece. Cover and door frame with circumferential seals for dust-free work. With stable grid shelf for depositing workpieces on the inside of the cabinet. With drain opening for changing the blasting agent. Extraction hose for blasting agent fastened on bottom of catchment container. With external compressed air coupling. Rubber feet for stable stand.

Technical data: cabin volume: 90l, air consumption: 200 - 350 l/min, working pressure: 2,8 - 8,0 bar, compressed air connection: 3,8", abrasive grain size: 40 - 120 mesh, dimensions: internal 580 x 480 x 300mm / external 590 x 489 x 490mm, weight: 17kg
Scope of delivery: high quality blasting gun with ceramic nozzle, 4 pieces ceramic nozzles (4/5/6/7mm), 12 Volt neon tube with 230 Volt power supply and external switch, incl. 5 pieces spare foils for view window, 2 large and integrated latex gloves

shortwave infrared
Strudy design made of aluminium and stainless steel. High quality V Power quartz halogen shortwave infrared tubes. Dries the paint layer efficiently from the outside and inside out, thereby bubbles are avoided and saves time. 360° swiveling and rotating lamp housing. Ball bearing rollers with parking brake.

Technical data: drying area length: 800mm, drying area width: 450mm, temperature: 30 - 0, time switch: 0 - 60 min, mains supply cable length: 4,5m, total rated value: 1 kW, supply voltage: 230V, current type: AC, mains frequency: 50 / 60 Hz, color temperature: 2500 K, degree of protection: IP21, protection calss: F

30 A, inverter technology, for all electrically conductive metals, up to 15mm for steel
The HF-free ignition extends the durability of the wear parts. The unit is suitable for maintenance and body work with its robust housing and simple control panel with flow meter. The inverter technology guarantees the cutting quality of all steels (soft, stainless, hardened, HLE), aluminum, copper, etc.... With potentiometer to adjust the current according to the thickness of the sheet. The air pressure is set manually (2.0 to 9 bar), the flow meter is located on the front.

MIG-MAG protection gas welding plants, 3 phase, half-synergic, with Euro burner connection, incl. accessory set
Suitable for welding steel, stainless steel, aluminiun and for MIG brazing of high-tensile strength steels with CuSI3 and CuAl8 wires, ideal for car body repairs. The wire speed is adjusted on the spool gun torch directly, to weld aluminium AISi5 and AISi12. With three modes: standard (2T), spot, plug welding function (spot welding with adjustable spot diameter) und delay, chain stitch function (spot welding with adjustable distance)

Technical data:
braze/welding area: 15 - 200A
welding wire guidance: 4 rollers
welding wire Ø: 0,6 - 1,0mm, suitable for wire roller Ø: 100, 200 or 300mm
duty cycle EN60974-1 (40°C): 25% / 150A
power supply: 400V/ 3 phase
dimensions: 47 x 77 x 79cm
Scope of delivery: 1 T1GYS AUTO, 1 torch, 1 massive coil - steel - SG2 - Ø 200mm - Ø 0,8mm - 5kg, 1 accessory set MB15 - 150A - for MIG torch, 1 pressure reducer - 2 pressure gauges (30 l/min), 1 welding helmet (LCD Fireman 9-13 true color)

MIG-MAG gas-shielded welding machine, three-phase, synergic controlled, with many accessories
Suitable for welding work in locksmith shops and automotive workshops. The wire feed unit can process 2 wire types and diameters. This avoids a loss of time when changing wire. The first wire feed unit is integrated in the unit and the second is located in a separate wire feed case, which is connected via an intermediate hose package. 2 torches enable selection of wire feed unit and control of welding parameters (gas among others). 2 electrovalves on the rear side of the unit enable the supply of 2 different gases. No need to change wire spools, wire guide roll and contact tubes. The plant can be used variably. It is suitable for welding steel, stainless steel and aluminum.