2-K polyester putty, with hardener, styrene-, asbestos- and silicone-free, white
Highly flexibole, quickly curing, temperature resistant with hardened material up to 120°C. To fill smaller imperfections and the thin fine plastered of already previously treated surfaces. Suitable for surfaces made of metal, wood, concrete or pre-filled with presto filling filler. Microfine fillers give a very smooth surface. Can be grinded after approx. 30 minutes, flash point at approx. 33°C, curing agent addition: 2 - 4%.

2-component polyester putty, incl. hardener
Mixture of medium-elastic, highly reactive, amine-accelerated polyester resin with various mineral, environmentally friendly fillers. Applicable to metal, wood, concrete. For filling holes and bumps, covering pre-treated surfaces when repairing body parts, etc. metal surfaces, repair and restoration of wood or concrete surfaces, e.g. steps, insertion of dowels and screws. Grindable after approx. 20 - 30 min., asbestos- and silicone-free, pot life at 20°C approx. 4 min., hardener addition 2 - 4%, temperature resistance on hardened material 120°C. Resistant to acids, bases, water and salts, suitable for stove enamel.

2-component putty, polyester resin-based, styrene-reduced, incl. hardeners, bright white
Adheres to iron, steel, aluminum, GRP and wood. Suitable as a top and fine filler for application in thin and very thin layers, as a top coat over PE filling putty, for closing any remaining pores or small irregularities and for removing minor paint damage, scratches, etc. on the bodywork. Application on vertical surfaces is possible without any problems. The styrene content is less than 10 %.

filler and finish putty, incl. hardener, beige
Adheres to sheet steel, galvanized sheets, aluminum, tinned surfaces, GRP and wood. Short drying time, easy to sand.

1-component acryl putty, quick drying, beige For equalizing of small bumps, scratches and pores on putty surfaces, priming surfaces or filler surfaces as well as on GRP or polished old sprayings. Apply only in thin layers also a direct adhesion to steel, aluminum, galvanized steel substrates and following plastics: ABS, PVC hard, PC, PS, PA, PP/EPDM, POM and A-PET. Due to the modified viscosity setting, a creamy consistency is given, which ensures a pore-free and easy application. Application only in thin layers, recoatable with all conventional paint systems.

2-component based on polyester resin, incl. hardener
Reduces styrene, very easy to sand, with adhesion to sheet steel, aluminum, zinc and GRP. Can still be sanded after 24 hours with a large abrasion. The proportion of styrene is lower as 10%.

asbestos-free 2-component putty, polyester resin base with aluminum pigmentation, incl. hardener, styrene-reduced
Specially designed for the high quality demands of vehicle construction and the repair trade in terms of processing, adhesive strength and sandability. The product is suitable for leveling depressions and unevenness on iron, steel, GRP and wood. Processing on vertical surfaces is possible without any problems. Properties: good sandability, high stability, high elasticity.

2-component polyester fiberglass filler, incl. hardeners
For bridging cracks, small holes and rust through in car repairs, in vehicle and machine construction and in the boat sector. Adheres to iron, steel, aluminum, zinc, GRP and wood. Waterproof, high stability, conditionally sandable.

2-component filler on polyester base, grey
For steel base, GFK, wood or ground, viable old coatings. Particularly suitable for filling of bumps, strong sanding marks as well as roughly preprocessed repair points in a single operation.

elastic contour putty, only dry sandable
Especially for use on removable plastic parts. Good adhesion to steel, iron, aluminium, GFK and wood. High elasticity, short drying time and easy to sand.