YUASA

Yuasa, standard

Standard batteries are dry pre-charged, fill the battery with the acid before use and leave open for approx. 1-2 hours, then attach bleeder hose and connect the battery.
Attention: by batteries from 12V evtl. must be recharged!

Yuasa, MTF

Acid pack included. After removing the adhesive tape, attach the supplied acid pack and let it run evenly in all cells, then let it stand for 1-2 hours and at the and fasten the sealing.
Once filled and sealed, further maintenance is not necessary.
Attention: 12V batteries can be a recharge required!
Never open, pirce/drill nor remove the sealing strip of these sealed (MTF) batteries!

Yuasa, MTF

Acid pack included. After removing the adhesive tape, attach the supplied acid pack and let it run evenly in all cells, then let it stand for 1-2 hours and at the and fasten the sealing.
Once filled and sealed, further maintenance is not necessary.
Attention: 12V batteries can be a recharge required!
Never open, pirce/drill nor remove the sealing strip of these sealed (MTF) batteries!

MTFsealed

Solves the problem of possible leaks in a conventional battery. The electrolyte (acid) consists entirely of a non-liquid gel. Even in the event of damage to the Housing of the Battery, this electrolyte cannot leak. It provides the ultimate protection against possible acid damage to the motorcycle or Wheels.
The service life of a gel battery is approx. 50 % longer than that of a conventional maintenance-free battery. According to the JB/4282-92 standard, a normal maintenance-free battery has a maximum service life of 200 charging cycles. This compares with up to 500 charging cycles for a gel battery.

Attention: Recharging only with so-called "intelligent charging devices" such as Optimate 4 and Intellicharger II. Damage caused by incorrect charging is not covered by the warranty!
Caution: Never open or drill into these sealed (gel) batteries or remove the sealing cap!

Yuasa, MTF, sealed

100% MTF - no need to refill water; necessary is only regular charging when not in use, first-class AGM technology (Absorbed Glass Matt) without free acid, sealed, leak-proof design for different installation positions, high performance OE battery, developed according to the individual specifications of the motorcycle manufacturers, sulfate barrier additive to prevent damage when the charge is too low, delivery is filled and ready for installation.

Yuasa, MTF, sealed

100% MTF - no need to refill water; necessary is only regular charging when not in use, first-class AGM technology (Absorbed Glass Matt) without free acid, sealed, leak-proof design for different installation positions, high performance OE battery, developed according to the individual specifications of the motorcycle manufacturers, sulfate barrier additive to prevent damage when the charge is too low, delivery is filled and ready for installation.

Yuasa, MTF

Acid pack included. After removing the adhesive tape, attach the supplied acid pack and let it run evenly in all cells, then let it stand for 1-2 hours and at the and fasten the sealing.
Once filled and sealed, further maintenance is not necessary.
Attention: 12V batteries can be a recharge required!
Never open, pirce/drill nor remove the sealing strip of these sealed (MTF) batteries!

MTFsealed
Solves the problem of possible leaks in a conventional battery. The electrolyte (acid) consists entirely of a non-liquid gel. Even in the event of damage to the Housing of the Battery, this electrolyte cannot leak. It provides the ultimate protection against possible acid damage to the motorcycle or Wheels.
The service life of a gel battery is approx. 50 % longer than that of a conventional maintenance-free battery. According to the JB/4282-92 standard, a normal maintenance-free battery has a maximum service life of 200 charging cycles. This compares with up to 500 charging cycles for a gel battery.

Attention: Recharging only with so-called "intelligent charging devices" such as Optimate 4 and Intellicharger II. Damage caused by incorrect charging is not covered by the warranty!
Caution: Never open or drill into these sealed (gel) batteries or remove the sealing cap!

Yuasa, MTF

Acid pack included. After removing the adhesive tape, attach the supplied acid pack and let it run evenly in all cells, then let it stand for 1-2 hours and at the and fasten the sealing.
Once filled and sealed, further maintenance is not necessary.
Attention: 12V batteries can be a recharge required!
Never open, pirce/drill nor remove the sealing strip of these sealed (MTF) batteries!

Yuasa, standard

Standard batteries are dry pre-charged, fill the battery with the acid before use and leave open for approx. 1-2 hours, then attach bleeder hose and connect the battery.
Attention: by batteries from 12V evtl. must be recharged!