Rubber / bitumen, compatible with PVC and bitumen, with anti-drumming effect, CFC-free, cannot be painted over, black
Protects the vehicle underbody from rust, stone chips and road salt. Particularly suitable for repair work and treatment of hard-to-reach areas on the vehicle underbody.

Light beige, transparent, low-viscosity corrosion protection for cavities
Water-repellent, temperature-resistant from -25 °C to +160 °C, with good creeping properties. Provides long-lasting protection for body cavities such as sills, pillars, door interiors and headlight housings. Resistant to water, road salt spray, Oil, light acids and alkalis.

wax spray, bitumen-free, PVC-compatible
For the preservation of vehicle bodies and rust-prone areas in the engine compartment. Suitable for repair work. Has a good creeping ability, does not drip and is suitable for long-term protection. Slight spraying of rubber parts gives a dull shine and fresh look

Can be painted over, compatible with PVC and bitumen
Protects vehicle floors, wheel arches, Spoilers, sills, doors and rear aprons from abrasion and corrosion. Contributes to maintaining the value of motor vehicles.

long-term sealing, forms a waxy, olive-brown film
For machinery, vehicles, winter maintenance vehicles, agricultural and construction vehicles, shafts, steel coils, semi-finished and finished products. Forms a compact waxy protective film that does not become brittle, protecting against most environmental, direct weather influences (including flue gas), atmosphere and salt water. Suitable also for protection and insulation of electrical cable lugs and screw terminals. Cab be removed by white spirit or petroleum solvents or "BRUNOX Turbo-Spray" when protection is no longer required

Note: Film thickness min. 20 µm. With a dry film thickness from approx. 50 µm, the best possible corrosion protection is achieved. A wet film thickness of 125 µm gives a dry film thickness of 50 µm. This requires a 0,63 l/m².

Wax-based, non-drip, mist-free
Protects vehicle floors, wheel arches, mudguards and other body parts from corrosion. Compatible with PVC and bitumen, with anti-drip effect, cannot be painted over.

aerosol wax polish and corrosion inhibitor
Suitable for the treatment of small, isolated places. Can be applied on layers based on PVC, PVC/wax, rubber/resin or KTL. OEM-specified, temperature resistant and creeping. With the additionally attached spray pipe also the cavities can be well achieved, e.g. in doors and in the engine compartment.

on rubber/resin basis, containing solvents, bitumen-free, black
For after treatment of difficult to access areas, such as angles, corners, edges, etc. in which preferably form rust nests and used for asbestos repair work on the vehicle underbody. In addition, with the innovative flat jet spray head, car undertrays can be optimally coated with a wide jet.Suitable for coating primed sheet on the underbodies and for repairing or supplementing existing coatings based on PVC or rubber / resin.

quick drying, permanently plastic protective film, transparent, cannot be painted
Protects and maintains body parts and metal parts. Suitable as preservative agend and corrosion protection. Has a very good creeping ability, high heat resistance and good cold flexibility. Is moisture resistant, resistant to water, salt water, brake fluid and many chemicals.

Corrosion protection and lubricants, thixotropic
The product is used for metal products, machines and sports equipment during storage and transportation in a closed environment (up to 3 years), in covered outdoor areas (up to 1 year) and in outdoor areas (up to 5 months). It forms a very even, non-drying corrosion protection film that also penetrates into corners and edges that are difficult to access. It is also resistant to acidic atmospheres and other environmental influences.

Note: The applied layer thickness should be approx. 5 - 20 μm, i.e. 20 - 40 m² of surface can be treated per liter. After protection, it can be cleaned with
detergents, e.g. anionic wetting agents.