rust protection, versatile universal primer
For repairs on cars, motorbikes, as well as other vehicles or metal surfaces. Quick drying, with good filling power, high efficient, adheres well. Can be used on substrates such as iron, steel, hardened and ground old coatings, well-dried Mipa 1K and 2K filler materials.

chromate-free 1K-repair filler based on epoxy resin
Also suitable as a corrosion protection primer and has a very high insulating effect against moisture. Can be used on sustainable , old ground paintwork and factory primers or directly on steel, aluminum and galvanized surfaces. Has a quick drying and very good griding ability. Due to the very fine atomization, run-off zones without coarse spray mist are possible in the spot repair area. Paintable with all common solvent and water-based 1K and 2K topcoat systems.

2-component wash primer, chromate-free, adhesion primer for non-ferrous metals
Acid-curing, chromate-free 2K primer especially for aluminum substrates with active corrosion protection and excellent adhesion to iron, steel and galvanized substrates. Can be overcoated with all Mipa 1-component and 2-component systems (exception: cannot be overcoated with epoxy paint systems and water-based base coats). Can also be applied in a three-coat process (active primer / filler / top coat). Yield: 8.0 - 10.0 m²/l

chromates 2K-epoxy resin material
For efficient car and large vehicle painting. Combines the properties of a filler and a primer. Adhesion resistant also on non-ferrous metals, therefore especially suitable for mixed construction. Very good filling power and adhesion on steel, aluminium, galvanized steel and GRP. Impact and scratch resistant, offers high corrosion protection and weather resistance, very good chemical and mechanical resistance. Recoat with polyester body filler after forced drying (30 minutes / 60 - 80°C) at dry film thickness up to max. 120 µm. Yield: 5,0 - 6,0 m²/l (at 40 - 50 µm TSD)

adhesion primer for a wide variety of substrates, UV-stable, colorless
Completely colorless, universal plastic primer for use on plastics commonly used in the automotive sector (e.g. PP-EPDM, ABS, PC, ABS-PC, PMMA, PA, PUR, PVC, GRP). Due to the special formulation, adhesion to other, difficult substrates, without prior sanding, is also possible without any problems. Mipa 1K-Haftpromoter can be used on steel, aluminum (also polished or anodized), galvanized substrates, stainless steel (also polished), non-ferrous metals (also polished), chrome-plated substrates, powder coatings and KTL coatings. The material offers great time savings due to fast drying and recoatability as well as the elimination of sanding. Can be painted over with Mipa 1-component and 2-component top coats. Mipa 1-component Adhesion Promoter is colorless and UV-stable and can therefore also be overpainted with Mipa clear coats.

acrylic, filling / adhesive primer,corrosion protection, between Brunox epoxy and the topcoat
For priming or pre-painting of metal surfaces, corrosion protection, forms a strongly adhering surface, runs well, dries quickly, equalizes smallest unevenness, reduces the topcoat consumption. Can be painted over with water-based paints, air-drying acrylic, synthetic resin and nitro combination paints. Dust-dry after 20 minutes, hold after 30 minutes, sandable after 2-4 hours.
Note: Do not spray on synthetic resin paints!

1-component primer, for spot repair or as thick-film filler
Designed specifically for small repairs and sanding points. Due to its very smooth course, no further intermediate sanding in the area of the spray mist zone is required. Can be painted directly wet-in-wet and adheres to iron, steel, zinc, aluminum and most plastics used in the automotive sector (PU, ABS, PC and PS - if necessary, carry out a test coat).
Note: Do not use on thermoplastic substrates!

1K-adhesive primer, acrylic-firm, weldability tested acc. to DVS 0501
With active corrosion protection for the vehicle area. Suitable for iron, steel, zinc and aluminum as well as overpaintable plastics used in passenger cars (if necessary, we recommend an overcoating test). Only work on well degreased surfaces. Sand zinc and aluminum. Do not use on thermoplastic substrates. Do not overwork with polyester spray filler. Paintable with solvent-based and water-dilutable 1K and 2K paints.

1K-rust protection primer
For industrial indoor and outdoor use of machinery, plant and equipment, metal constructions etc. made of steel. With high content of zinc phosphate, weather resistant, very good running, adhesive, impact, scratch and water resistant.
Note: Only for the professional application. Cannot be painted over with high solid Mipa 2K topcoats. Outdoor storage of approx. 5 days is possible without a top coat.

1-component primer, corrosion protection
Has a very good adhesion and very high filling power. Due to the very large material output, a high working speed with high layer thicknesses is guaranteed. Also, hard-to-reach areas can be more easily coated due to the wider spray jet. Adheres to iron, steel, zinc and, with appropriate pre-treatment, to aluminium as well as to overcoatable plastics in the passenger car sector (if necessary, we recommend an overcoating test).