HSS-CO, type N, with 5% cobalt, DIN 338
Cylindrical, short, right, polished, tips from 3mm split point, sharpening angle 135°. Suitable for alloyed and unalloyed steels (700 - 1300 N/ mm²),hot and cold work steels, tempering and case-hardening steels and stainless and acid resistant steels

HSS-TIN, type N, titanium coating, DIN 338
cylindrical, short, right, sharpened, titanium coating, from Ø 3mm cross-grinding, sharpening angle: 135°. Suitable for steel, cast steel alloyed and unalloyed ( lower as 900 N/mm²), grey and die-cast, sintered iron, graphite, short-chipping aluminum alloys, brass and bronze

HSS-R, type N, roll-milled, DIN 338, black
Cylindrical, short, right, standard , sharpening angle 118°. Suitable for steel, cast iron alloyed and unalloyed ( lower as 900 N/ mm²), grey and pressure casting, sintered iron, graphite, short-chip aluminium alloys, suitable for brass and bronze

HSS-Co, type N, with 5% cobalt, DIN 338, in steps of 0,5mm
Cylindrical, short, right, polished, tips from 3mm cross grinding, sharpening angle 135°. Suitable for alloyed and unalloyed steels (700 - 1300 N/ mm²), hot and cold work steels, tempering and case-hardening steels and stainless and acid resistant steels

HSS-TIN, DIN 338, Ø 1 - 10mm, in steps of 0,5mm, 19 pieces
cylindrical, short, right, sharpened, titanium coating, from Ø 3mm cross-grinding, sharpening angle: 135°. Suitable for steel, cast steel alloyed and unalloyed ( lower as 900 N/mm²), grey and die-cast, sintered iron, graphite, short-chipping aluminum alloys, brass and bronze

DIN388, HSS M2, cylindrical, short, cross ground, step drill tip geometry from 2.5 mm, 3-flute shank from 4.0 mm
High-precision, high-performance spiral drill for universal use on smooth, rounded and uneven surfaces. Ideally suited for use in hand-held machines, e.g. cordless screwdrivers and electric drills, as well as pillar drills. The drills eliminate the need for pre-drilling, enable precise spot drilling without running and angled drilling and are very suitable for drilling out rivets and stud bolts.

HSS-G M2 / S2, 1/4", hexagonal, 38 pcs.
Tool set with short spiral drill bits, screw bits and lever-action ratchet (mini). These short metal spiral drills are suitable for drilling into metals such as steel, cast iron or sintered iron using a cordless screwdriver. The 1/4" hexagonal shank enables quick bit changes. They also fit into any conventional bit holder as well as 3-jaw chucks.

Consisting of:
9x twist drill bits: ø 3.0, 4.0, 4.5, 5.0, 5.5, 6.0, 7.0, 8.0, 10.0 mm
25x bits, inside hexagon / T-profile / T-profile with hole / slotted / cross / Pozidriv
1x micro-bit lever-action ratchet
1x Adapter, 1/4 square x 1/4 hexagon
2x bit holders with quick-change chuck, 67 mm / 150 mm

HSS-R, DIN 338, in steps of 0,5mm
cylindrical, short, right, rolled, black, standard polish tips, sharpening angle: 118°. Suitable for steel, cast steel alloyed and unalloyed ( lower as 900 N/mm²), grey and die-cast, sintered iron, graphite, short-chipping aluminum alloys, brass and bronze

HSS-G, type N, DIN 338, in 0,5mm steps
cylindrical, short, right, sharpened, blank, from 3mm Ø cross-grinding, sharpening angle: 135°. Suitable for steel, cast steel alloyed and unalloyed ( lower as 900 N/mm²), grey and die-cast, sintered iron, graphite, short-chipping aluminum alloys, brass and bronze

for non-ferrous metals, plastic, plasters, suitable for Micromot systems
Wolfram-vanadium steel. For use on hard and soft woods, non-ferrous and precious metals, as well as plastics and plasters. Shaft Ø 2,35 or 3,0mm. Especially suitable for finishing, forming, profiling and grooves.