1/2" drive with 8mm mount, for clockwise/counter-clockwise operation, for loosening tight screw connections, 8 pieces

Technical data:
cassette toal dimensions (LxWxH): 195 x 58 x 45mm

Consisting of:
1x hand impact wrench
1x Kraftbit (Phillips) PH1, length: 35,7mm
1x Kraftbit (Phillips) PH2, length: 35,7mm
1x Kraftbit (Phillips) PH3, length: 35,7mm
1x Kraftbit (Phillips) PH4, length: 35,7mm
1x Kraftbit (slot) 8mm, length: 35,7mm
1x Kraftbit (slot) 10mm, length: 35,7mm
1x Kraftbit (slot) 12mm, length: 35,7mm

hollow head, plastic coated steel handle with rubberized grip, length: 275mm, temperature resistance from -20 to +90°C, head Ø: 35mm, head weight: 420g

1/2" drive with 8mm mount, for clockwise/counter-clockwise operation, for loosening tight screw connections, 13 pieces

Technical data:
cassette total dimensions (LxWxH): 195 x 58 x 45mm

Consisting of:
1x hand impact wrench
1x Kraftbit (Phillips) PH1, length: 35,7mm
1x Kraftbit (Phillips) PH2, length: 35,7mm
1x Kraftbit (Phillips) PH2, length: 79,8mm
1x Kraftbit (Phillips) PH3, length: 35,7mm
1x Kraftbit (Phillips) PH3, length: 79,8mm
1x Kraftbit (slot) 8 mm, length: 35,7mm
1x Kraftbit (Torx) T40, length: 35,7mm
1x Kraftbit (Torx) T45, length: 35,7mm
1x Kraftbit (inside hexagon) 4mm, length: 35,7mm
1x Kraftbit (inside hexagon) 5mm, length: 35,7mm
1x Kraftbit (inside hexagon) 6mm, length: 35,7mm
1x Kraftbit (inside hexagon) 8mm, length: 35,7mm

6 pieces, chrome-molybdenum-vanadium air hardening steel (45CrMoV7)
Hardened and tempered over its full length. Impact heads inductive tempered, polished and painted working ends.

Consisting of:
1x 8-point flat chisel, cutting width: 12mm, length: 125mm, shaft Ø: 10mm
1x 8-point flat chisel, cutting width: 16mm, length: 150mm, shaft Ø: 12mm
1x 8-point cross-cut chisel, tip: 5mm, length: 125mm, shaft Ø: 10mm
1x 8-point drift punch, tip: 3mm, length: 120mm, shaft Ø: 12mm
1x center punch, tip: 4mm, length: 120mm, shaft edges: 10mm
1x pin punch, tip: 4mm, length: 150mm, shaft Ø: 10mm

Forged hammer head from special tool steel, carefully hardened and tempered, painted with black water varnish and ash handle. Striking face and pein polished, regular edge break, hardened handle sleeve protection. Handle protection by ring wedge

double curved ash ahndle, DIN 5111
With additional hardened handle protective steel sleeve, ring wedge, fixing plate and wood screw. With this standardized wooden handle DIN 5111 every DIN hammer head can be made as a Rotband-Plus hammer.
Application: Drive the handle into the hammer head up to the sleeve. Drive the ring wedge into the intended borehole. Tighten the locking plate with the screw on the hammer head.

normal version, total length: 150mm, 5 pieces
DIN 6450 form C, ergonomic 2-components hand guard, hand guard length: 75mm, blade length: 75mm, chrome-vanadium, air hardened. Depressant effect - less stress to the hand due to impacts. Consisting of: each 1x Ø 3 - 4 - 5 - 6 - 8mm

plastic, Desmopan head, non-rebound, replaceable
Joint-protecting, ergonomic handle; environment-friendly and breathable ash handle, zinc-cast centre part with protective guide bush for the handle

chisel and centre punch, 6 pieces, chrome-vanadium, air hardened, consisting of: #731-2, #731-5, #741-1, #745-3, #745a-4, #746-1

chrome-vanadium, air hardened, in plastic stand-box, 6-pieces, consisting of: each 1x #748a-2, #748a-3, #748b-4, #748b-5, #748c-6, #748c-8